Formula Fun owner support

Get your board
ready to ride.

Fit your fins. Connect your leash. Put your Tahoe together. Find the demonstration for your board, then keep it in good shape between sessions.

Follow along

Your setup guides.

Real Formula Fun demonstrations.
Choose a task or browse all four guides.

4 guides

Official Formula Fun Tahoe unboxing and assembly video cover10:05

Tahoe · full walkthrough

Unbox and assemble your Tahoe

The full Formula Fun film covers unboxing and assembling the three-piece SUP. Keep the illustrated instructions nearby as you work.

  • Check the three board sections, four connecting tubes and four pins.
  • Use the board and fin instruction sheets below for the locking and fin hardware.
Open on YouTube : Tahoe 3-Piece Stand Up Paddleboard Unboxing & Assembly | Best Portable SUP for Travel
Formula Fun Foam Boards · YouTubeVideos load when you press play. You can always open the original.

Before you fit a fin

Same fin count.
Not always the same parts.

The board in the demonstration matters. Match your model and fin box before ordering or fitting hardware.

Help me identify a part
DOHO
2 + 1: center fin and two side bites. Use the DOHO film above.
Zippers
Three-fin thruster. The Zippers fin and leash films show this board.
Canyon & Jam
Also thrusters. Their three-fin layout does not make every Zippers part interchangeable.
SanO
2 + 1 setup. Match the SanO’s center fin and side-bite hardware to your own board.
Another model?
For Twinnie, Rincon, Rubicon, Bodyboard or an older board, send the model and a clear photo of the connection.

Tahoe owner’s corner

Three pieces.
One paddleboard.

Start with the full unboxing and assembly film above. Use this short overview to see how the sections come together, and the illustrated sheets for the details.

Watch the full 10:05 guide

Set out your kit

Three board sections · four connecting tubes · four pins

Adjustable paddle · coil leash · 9″ fin

Keep the specified screwdriver and fin hardware handy. The illustrated sheets show the board locking step and the fin’s plate-and-screw fitting.

The quick visual overview0:12 · Formula Fun · the full setup film is 10:05

Keep the instructions
beside your board.

Open a sheet to see the connections and hardware at full size.

Tahoe · boardConnect the three sections

The board sheet shows the tubes, pins and locking sequence. Follow its illustrated orientation and tool directions.

Open the full-size board instructions ↗Formula Fun Tahoe illustrated board assembly instructions
Tahoe · finFit the center fin

The fin sheet shows the plate-and-screw fitting and Phillips screwdriver. Check the pieces against the drawing before starting.

Open the full-size fin instructions ↗Formula Fun Tahoe illustrated center fin installation instructions

Need the original resource? Open the Tahoe assembly page ↗

Between sessions

A good rinse.
A cool place.
Ready for next time.

Rinse

Use fresh water to remove salt, sand and dirt after a session. Skip solvents and household cleaners.

Dry

Wipe the board down with a clean cloth or towel. Let it dry before putting it in a board bag or sock.

Store

Keep it somewhere cool and dry, out of direct sunlight and away from chemicals.

The things owners ask.

Should I wax the deck pad?

No. Formula Fun’s care guide says not to wax the EVA deck pad; wax can be very difficult to remove. Rinse away sand and dirt instead.

Can I leave it in the sun?

Avoid extended heat and sun exposure when you are off the water. It can bubble or fade the deck pad. Store the board cool, dry and shaded.

How should I transport it?

Use a board bag when mounting it on a vehicle. Do not overtighten roof-rack straps; excessive pressure can crease the rails. Check your rack and board setup before travel.

There’s a ding, loose part or damaged pad.

Send a photo of the whole board and a close-up of the issue. Tell us how it happened, if you know. We can help identify the next step for that board before you choose a repair material or replacement part.

Prepare a help request ↓
Read the full Formula Fun care guide ↗

A person can help

Show us
what you’ve got.

A clear photo gets us closer to the right part or next step. You don’t have to know the name of the fitting.

  1. The whole boardBoth sides, with the model name or graphics visible.
  2. The connection or issueA close-up of the fin box, plug, fastener or damage. Include any loose pieces.
  3. Your order, if you have itOrder number, purchase date and where you bought it. For an older board, an approximate year helps.

Send the details below. If photos would help, email them to hello@formulafunboards.com with your name and order number.

hello@formulafunboards.com

Get your message started

Choose your board and tell us what you need. Send the details to our team for help.

Include your board model, order number if available, and the help you need.

Or use the contact page ↗